Which machine should I choose to grind superfine talcum powder?

Talc powder is obtained by crushing and grinding talc blocks. The talc powder is calculated according to the mesh. The higher the mesh, the finer the talc powder. Common talcum powder has 600, 800, 1000, 1500, 2000, 2500, 3000 meshes. According to the different fineness of talcum powder, it can be used in different places, such as chemical grade rubber, plastic, paint, etc., ceramics, cosmetics, medicine and food. , Papermaking, etc.

talc powder

Ultra-fine talcum powder can be used for the filling of advanced coatings, paints, cosmetics, plastics and other products. It can make the concentration of paint thicker and more uniform. It is transparent when soluble in water. It not only does not affect the color of plastics, but also enhances the toughness of plastics.

How To Get Superfine Talcum Powder? 

The following mainly introduces two machines that can be used to grind superfine talcum powder: HGM micro powder grinding mill and CLUM ultrafine vertical mill.

These two machines are new type of ultrafine grinding equipment integrating powder grinding, grading, conveying, secondary powder selection, and finished product packaging. They are both widely used in grinding. non-flammable and non-explosive materials under 7(the Moh’s hardness), such as quartz, feldspar, calcite, talcum, barite, fluorite, iron ore, copper ore quartz, especially for slag, cement clinker, zircon sand, fly ash and carborundum, coal, etc.

HGM micro powder grinding mill and CLUM ultrafine vertical mill both can be used to grind and produce ultra-fine talcum powder. They have high grinding efficiency and high production capacity. Compared with ordinary grinding machines, the output is increased by 40%, and the energy consumption is reduced by about 20% to 30%. All adopt a closed system, pulse bag filter and muffler, with low noise, less dust, and environmental protection. Both grinding rings and rollers made of special materials are used, with low wear rate, less metal pollution and long service life.

What is the Difference Between Them?

CLUM ultrafine vertical mill

Suitable for large capacity production, output: 0.2-45 tons/hour, final product fineness 325-3000 mesh

The finished product obtained has high whiteness, fine particle size and good sphericity

Powerful drying ability: drying and grinding raw materials with a moisture content of up to 15%.

CLUM ultrafine vertical mill

working principle:

When working, the main machine grinding disc rotates under the action of the reducer, and the material is evenly fed into the grinding chamber by the feeder. Under the action of centrifugal force, it spreads around. When passing through the roller table area on the grinding disc, the pressure of the grinding roller is large. The block material is directly crushed, and the small particle material is subjected to inter-particle grinding and pulverization after being pressed to further pulverize until it becomes powder.

HGM micro powder grinding mill

Final product fineness 200-2500 mesh

It is easy to use, simple to operate, small in size, and does not occupy space.

Intelligent frequency conversion speed control device: uniform input of materials, large particle size of the finished product, and high particle size cutting precision.

CLUM ultrafine vertical mill

working principle:

When the micro powder grinding mill is working, the crushed materials are sent to the main machine evenly by the feeder, and scattered to the four walls of the grinding chamber under the centrifugal force. The grinding roller rotates under the action of the reducer, and the material is repeatedly squeezed and crushed between the grinding roller and the chamber wall. The ground powder is brought to the classifier by the airflow, and the qualified powder is finally collected by the classifier, and the unqualified powder will fall into the grinding chamber and continue to be ground.

You can choose the machine according to the actual production needs. As long as you leave us a message about the material you want to process and the fineness of the final product, our technicians will provide you with the most reasonable solution for free. Of course, you can also contact us directly to inquire.


Copyright 2015 by Shanghai Clirik Machinery Co. LTD All rights reserved